Konfigurasi EIGRP Pada Cisco Paket Traser
1. Buatlah topologi atau kerangka dari desaint yang kita inginkan
2. Klik Router-PT (0) lalu pilih CLI:
3. Klik Router-0 lalu tuliskan konfigurasi seperti dibawah ini
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#ex
Router(config)#int se2/0
Router(config-if)#ip add 10.10.4.1 255.0.0.0
Router(config-if)#band 64
Router(config-if)#cl ra 64000
Router(config-if)#no shut
%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#ex
Router(config)#router eigrp 2
Router(config-router)#net 192.168.1.1
Router(config-router)#net 10.10.4.1
Router(config-router)#ex
Router(config)#end
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#wr
Building configuration...
[OK]
|
4. setelah itu ganti ke Router 1 dan isikan konfigurasi seperti dibawah
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.2.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#ex
Router(config)#int se2/0
Router(config-if)#ip add 10.10.4.2 255.0.0.0
Router(config-if)#band 64
Router(config-if)#no shut
Router(config-if)#
%LINK-5-CHANGED: Interface Serial2/0, changed state to up
Router(config-if)#ex
Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up
Router(config)#int se3/0
Router(config-if)#ip add 172.16.2.1 255.255.0.0
Router(config-if)#band 54
Router(config-if)#cl ra 64000
Router(config-if)#no shut
%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#exit
Router(config)#end
Router(config)#router eigrp 2
Router(config-router)#net 192.168.2.1
Router(config-router)#net 10.10.4.2
Router(config-router)#
%DUAL-5-NBRCHANGE: IP-EIGRP 2: Neighbor 10.10.4.1 (Serial2/0) is up: new adjacency
Router(config-router)#net 172.16.2.1
Router(config-router)#ex
Router(config)#end
Router#wr
Building configuration...
[OK]
|
5. Kemudian ganti ke Router 2 dan masukkan skrip seperti dibawah ini
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.4.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#ex
Router(config)#int se2/0
Router(config-if)#ip add 172.16.2.2 255.255.0.0
Router(config-if)#band 64
Router(config-if)#no shut
Router(config-if)#
%LINK-5-CHANGED: Interface Serial2/0, changed state to up
Router(config-if)#end
Router(config)#router eigrp 2
Router(config-router)#net 192.168.4.1
Router(config-router)#net 172.16.2.2
Router#wr
Building configuration...
[OK]
|
6. Lalu cek keberhasilan dengan Kirim Pesan Ke Router 1 ke Router 2 dan Router 3 jika konfigurasi yang kalian masukkan sudah benar maka semua item akan successful :
Demikianlah konfigurasi EIGRP yang bisa saya berikan semoga bermanfaat bagi kita semua.
Konfigurasi EIGRP Pada Cisco Paket Traser
Reviewed by inspirasi wagu
on
November 19, 2019
Rating:
No comments: